Scania Service Repair Manual
Scania Error Codes
Scania Workshop & Bodywork provides a complete list of documentation necessary for the maintenance and repair of Scania trucks.
To work with Scania Workshop & Bodywork, you must have Adobe Acrobat Reader version 5.0 and higher on your computer.
All documentation in Scania Workshop & Bodywork is divided into 19 chapters according to subject.
0 General
1 engine
2 cooling system
3 fuel system
4 clutch
5 Gearbox
6 driveshaft
7 Front axle
8 Rear axle
9 Hubs and wheels
10 brakes
11 frame
12 pendant
13 Steering
14 Engine controls
15 Hood
16 Electrical equipment
17 Devices
18 Cabin
19 Accessories
Scania truck repair manual are includes:
· electrical wiring diagrams
· gearbox repair manual
· Air conditions troubleshooting and repair
· fault codes
· clutch repair manual
Removing the central gear RB662
Work description
1. Take the load off the axle housing before removing the central gear.
2. Trucks with leaf spring suspension must be supported under the frame or springs
as illustrated.
3. Loosen the nuts for the spring bolts (3), but leave them threaded a few turns.1
4. Tap in the spring bolts slightly.1
5. Remove the screws (2) and keep the shims (4).1
6. Remove the connecting member (1)1
7. Loosen the nuts for the half shaft flanges, but leave them threaded a few turns.
Clean the threads in the puller holes using a pilot tap, and screw in three screws
so that the flange exerts tension on the cones. Carefully tap on the half shaft
flange with a copper sledge hammer until the cones come loose.
8. Remove the nuts, cones and half shaft flanges, and pull out the half shafts approx.
20 cm.
9. Drain the oil from the axle housing (also refer to the oil section).
10. Detach electrical cables and compressed air lines for the differential locks.
11. Remove the propeller shafts.
12. Remove brake components that are in the way.
13. Undo all nuts except 2 (one in each upper side) securing the central gear.
14. Attach the central gear to the jack using the tools as illustrated.
15. Remove the 2 remaining nuts securing the central gear and pull it out from the
rear axle housing.
Scania P-, G-, R-, T- series Workshop manual
Scania K-, N-, F-series Workshop Manual
Scania industrial engines operator’s and service manuals
Scania Electrical Wiring Diagrams
Scania spare parts catalogs
Other manuals for Scania trucks
These troubleshooting instructions apply to trucks and two-axle buses. Three-axle buses are covered where applicable. This description covers the troubleshooting procedure for the retarder itself. The objective is to determine whether dismantling is necessary or not.
Spot repairs are often sufficient to make the vehicle operable again. All work on the etarder must be carried out with the most thorough cleanliness possible.
Scania - the world famous Swedish brand - the world leader in the production of trucks, comfortable buses, as well as the most economical industrial and marine diesel engines. Scania has become synonymous with efficiency, reliability and durability.
Mohd Azman Abdullah (Monday, 20 September 2021 06:29)
Thanks
Palitha Wijeratne (Sunday, 24 January 2021 08:22)
Dear Sir/Madom,
Kindly arrange to send me the SCANIA DC16.43A INDUSTRIAL ENGINE SPARE PARTS catalogue with part nos to order our ENGINES UNDER REPAIRS.
Pl refer the attached list of spares needed for the OVERHAUL.
Palitha Wijeratne (Saturday, 16 January 2021 07:04)
Dear Sir,
Kindly arrange to send me the SCANIA-DC16.43A ENGINE SPARE PARTS CATALOGUE to order COMPLETE OVERHAUL OF this engine here in SRI LANKA.
COMPLETE LIST OF ITEMS-need to repair present engine
(1) All required seals, rings & hardware
(2) All required sets of AIR, DIESEL, Hydraulic & Oil filters are essential.
(3) All-set of V-Belts of alternators, pumps etc. if applicable.
(4)
image.png
<image.png>
(5) Top Gasket Kits- All the parts required to remove and refit a cylinder head
(6) Valve train Kits-Valve train components for cylinder head overhaul
(7) Overhaul Re-ring Kit-Liner and piston rings for a more cost effective overhaul
(8) Overhaul Kit-all the parts required to complete a piston, ring and liner replacement
(9) Block heater
(10) Fan belts
(11) Full flow oil filter
(12) Bypass oil filter
(13) Fuel filters
(14) Air filter
(15) Supply All connected HOSES as well
(16) Any Essential Parts in addition you recommend to buy??????
Please LIST OUT ALL THE ITEMS & THE NO OF ITEMS to be purchased in an EXCEL SHEET, with total in EURO &
with your payment terms & conditions with BANK DETAILS etc. will be very much helpful to us to prepare the payment.
This means, if you quoted for the both ways as I mentioned above, we are definitely get the approval for the TOTAL REPAIRS or REPLACEMENT OF USED ENGINE, by definitely discussing with our customer & their Directors.
Kindly await your positive favorable answer, please.
Please send me the E-mail reply with your quote!!!
Thank you so much,
Best Regards!
Palitha Wijeratne-(Director)
POWERCO ENGINEERING (PVT) LTD,
{Ex-Senior Plantation/ Mechanical Engineer-Walker Sons & Co Ltd & Brown & Co. Ltd}
{Ex. Senior Material Consultant -LOADSTAR (PVT) LTD}
No-16/G/4, Greenwood Gardens,
Kahantota Road, Malabe-10115,
SRI-LANKA.
Tel: 0711-444780; E-mail: spwijey@gmail.com
Jank (Tuesday, 29 October 2019 19:58)
Javad
Hi, reloaded.
Javad (Tuesday, 29 October 2019 17:15)
Hi.How are you?
why can't download "Scania Wiring diagram handbook PDF"
Anele Ncube (Thursday, 19 September 2019 18:57)
Thank you. Very informative